Yanmar 4JH110 Fuel Filter Replacement
A clogged fuel filter starves your Yanmar 4JH110 of fuel — hard starts, hesitation and lost power at speed. Below is the exact filter that fits, a step-by-step video, and the symptoms to look for.
Check today’s price on Amazon →
Watch: how to do it (step by step)
How to Replace Fuel Filter – Yanmar 3JH4
Yanmar Engine Basics 2 – Fuel Filter
Yanmar 3JH4 Fuel Filter Replacement Guide
Tools Needed
- Oil filter wrench
- New Yanmar 3JH4 fuel filter (with o-ring)
- Engine oil for lubricating the o-ring
Safety
- Always ensure the engine is off and has cooled down before starting any maintenance work.
- Wear appropriate gloves to protect your hands from engine fluids.
Steps
- Place a container underneath the fuel filter to catch any dripped fuel.
- Using an oil filter wrench, unscrew the fuel filter by turning it counterclockwise until it is loose enough to remove by hand.
- Lubricate the o-ring of the new fuel filter with engine oil.
- Screw on the new fuel filter by hand, turning it clockwise until it is snug.
- Tighten the fuel filter further using the oil filter wrench, but be careful not to overtighten (around 1/8 to 1/4 of a turn after it's snug).
- After replacing the fuel filter, prime the fuel system by turning on and off the engine's electrical system or ignition switch three to four times, allowing about three seconds between each action.
Tips
- Always use oil to lubricate the o-ring of any filter you install on an engine, including fuel filters.
- If you're sailing in the Caribbean, be prepared to change your fuel filter more frequently due to potential debris and water in the fuel.
Which part do I need for my Yanmar 4JH110?
For most 4JH110 owners the part above (121857) is the right choice. Price tip: the aftermarket numbers are usually noticeably cheaper than the OEM-branded box — it is the same physical part. If you need an exact match, these compatible part numbers also fit:
Show all compatible part numbers (2)
| Part number | Description | |
|---|---|---|
| YAN129470-12330 | AIR FILTER ELEMENT | Find on Amazon → |
| YAN129A00-55800-HD | FUEL FILTER | Find on Amazon → |
Many of these are the same physical part under different brand numbers. Confirm against your engine plate before ordering.
Frequently asked questions
What fuel filter fits a Yanmar 4JH110?
The Yanmar 4JH110 uses the fuel filter sold as 121857, plus its OEM and aftermarket cross-references (2 compatible numbers are listed above). Confirm the number against your engine's model code and year plate before ordering.
How often should I replace the fuel filter on a Yanmar 4JH110?
Replace the fuel filter once a season or per the service manual — and sooner after a batch of dirty fuel or water in the separator.
What are the symptoms of a clogged fuel filter on a Yanmar 4JH110?
Hard starting, hesitation or surging under load, stalling at higher throttle and a general loss of power. The engine typically runs fine at idle and starves when fuel demand rises.
Do I need to bleed or prime the fuel system afterwards?
On diesel engines, yes — air must be bled from the fuel system after the filter change, and the video shows the procedure. On petrol outboards, squeeze the primer bulb firm before starting.
How long does a fuel filter change take on a Yanmar 4JH110?
Usually 30-60 minutes including priming or bleeding — a straightforward DIY job with basic tools.
Related guides
- Yanmar 2GM20 fuel filter
- Yanmar 3GM30 fuel filter
- Yanmar 3GM30F fuel filter
- Yanmar 2GM20F fuel filter
- All Yanmar maintenance guides
- Free Yanmar boat valuation
As an Amazon Associate we earn from qualifying purchases — at no extra cost to you. Prices and availability are shown at checkout. This guide is for reference; always follow the engine manufacturer’s service manual.