Honda BF200 Oil & Filter Change
Fresh oil and a new filter are the cheapest insurance for your 200 hp Honda BF200. Below is the exact oil filter that fits, a step-by-step video of the full oil change, and what else you need for the job.
Check today’s price on Amazon →
Watch: how to do it (step by step)
How to Replace Oil Filter – Honda BF250
Honda 200hp service and winterize. Gear lube, oil change, fuel and engine winterize.
Tools Needed
- Screwdriver (Philips)
- Vacuum pump
- Oil filter wrench
- Oil drain pan
- Funnel
- Compressed air
- Grease gun
Safety
- Ensure the engine is cool before starting any work.
- Wear appropriate protective clothing to avoid oil and grease stains.
Steps
- Locate the lower unit oil level plug and drain plug.
- Loosen and remove the oil level plug and drain plug.
- Remove the vent plug first, then the drain plug.
- Vacuum out the old gear lube from the lower unit.
- Remove the engine cover to access the oil filter.
- Vacuum out the old engine oil through the dipstick tube.
- Remove the old oil filter and replace it with a new one.
- Ensure the new oil filter's gasket or O-ring is lubricated with motor oil.
- Tighten the new oil filter securely.
- Drain the secondary fuel filter.
- Blow out the old fuel filter with compressed air.
- Install a new fuel filter and ensure a good seal with the O-ring.
- Fill the lower unit with new gear lube until it starts to overflow.
- Tighten the lower unit oil level plug first, then the drain plug.
- Tilt the engine up to access the grease fittings.
- Grease the grease fittings, including the trim and steering stem.
- Check the fuel level and ensure it is more than half a tank.
- Disconnect the fuel lines and pump out the fuel from the system.
- Disassemble the fuel system and install new filters.
- Prepare the Vapor Separating Tank (VST) for winterization.
- Open the VST drain plug and disconnect the pink hose.
- Connect the antifreeze pump and prime it.
- Start the engine and run the antifreeze through the system.
- Open the screw to pump out all the fuel from the fuel system.
- Vacuum out the remaining old engine oil.
- Fill the engine with new oil, using a funnel to avoid spills.
- Run the engine briefly to ensure proper oil circulation.
Tips
- Use a vacuum pump to efficiently remove old oil and gear lube.
- Ensure all new filters are properly sealed and lubricated.
- Tilt the engine to access all grease fittings for thorough lubrication.
- Use compressed air to clean out old fuel filters.
- Follow the manufacturer's recommendations for oil and antifreeze types.
Which part do I need for my Honda BF200?
For most BF200 owners the part above (18-7909) is the right choice. Price tip: the aftermarket numbers are usually noticeably cheaper than the OEM-branded box — it is the same physical part. If you need an exact match, these compatible part numbers also fit:
Show all compatible part numbers (4)
| Part number | Description | |
|---|---|---|
| 15400 | Oil filter | Find on Amazon → |
| Honda 15400-POH-305PE, 15400-PFB-007 | Oil filter | Find on Amazon → |
| Nissan 3R0-07615-0 | Oil filter | Find on Amazon → |
| Yamaha 5GH-13440-00-00 | Oil filter | Find on Amazon → |
Many of these are the same physical part under different brand numbers. Confirm against your engine plate before ordering.
Frequently asked questions
What oil filter fits a Honda BF200 (200 hp)?
The Honda BF200 uses the oil filter sold as 18-7909, plus its OEM and aftermarket cross-references (4 compatible numbers are listed above). Confirm the number against your engine's model code and year plate before ordering.
How often should I replace the oil filter on a Honda BF200?
Change the oil and filter every 100 running hours or once a season, whichever comes first (check your manual for the exact interval).
What else do I need for an oil change on a Honda BF200?
The correct grade and amount of engine oil (see the manual or the video), a new drain-plug washer, a filter wrench and a drain pan or oil extractor pump. Nothing exotic — it is standard service equipment.
What are the signs the oil is overdue on a Honda BF200?
Dark, gritty oil well past its interval, low-pressure warnings — and milky or grey oil, which means water is getting in and should be investigated immediately.
How long does an oil change take on a Honda BF200?
About an hour for a competent DIYer. Run the engine warm first — warm oil drains faster and carries more contaminants out with it.
Related guides
- Honda BF40 oil filter
- Honda BF150 oil filter
- Honda BF50 oil filter
- Honda BF90 oil filter
- All Honda maintenance guides
- Free Honda boat valuation
As an Amazon Associate we earn from qualifying purchases — at no extra cost to you. Prices and availability are shown at checkout. This guide is for reference; always follow the engine manufacturer’s service manual.